Megaware SkegPro SP655

Megaware SkegPro® protects your motor’s skeg from abrasion and damage due to rocks, sand, and submerged objects.

• Protects Against Ramp Dragging, Rock, Debris, and Submerged Objects
• Drain Hole Prevents Corrosion and Freezing
• A Model to Fit Virtually Any Skeg
• Do-It-Yourself Install in Less than 10 Minutes
• Constructed of 18 Gauge Marine Grade 304 Stainless Steel
• Mirror-Polished Finish Creates a Custom Look
• Conforms To Your Lower Unit to Ensure There Is No Discernible Drag Or Compromise In Performance
• Drain Hole On The Bottom To Prevent Water From Collecting And Becoming Stagnant And Causing Corrosion
• Do-it-yourself In Less Than 10 Minutes
• Comes With Stainless Steel Self-Locking Hardware
• Dimension Size: 2.54 x 12.7 x 40.64 cm

Megaware SkegPro Skeg Protector
Rocks, sand, debris, and submerged objects can damage your motor’s skeg. Avoid expensive repair costs and provide lasting protection with the Megaware SkegPro. The SkegPro prevents and reduces the amount of wear and abrasion to your skeg’s leading edge. It also reduces the amount of damage to your skeg when hitting minor objects or submerged stumps, rocks, and debris.

SkegPro Engineering
The SkegPro design features a mirror-polished finish enhancing its appearance and creating a custom look for your motor. It conforms to the skeg, ensuring no discernible drag or compromise in the performance of your engine. A drain hole prevents water from collecting, remaining stagnant, and potentially causing damage.

The SkegPro is available for most outboard and Inboard/Outboard (I/O) or Sterndrive engines, including Evinrude, Honda, Mercury, Mercruiser, Mariner, Suzuki, and Yamaha.

SkegPro Installation
Installation is a straightforward 4 step process and takes less than 10 minutes. Additional tools needed are gloves, a mallet (leather, rubber, or wooden), and a 3/16″ drill bit and drill.

Caution: Always wear gloves to prevent injury from cuts when working with this product.

Step 1) Determine Skeg Fitment
Before installing the SkegPro, visually check the fit by holding the SkegPro up against your skeg. If your skeg is damaged or worn, you will have to make some positioning adjustments when seating the SkegPro.

Keep in mind that some models are universal and will overhang from the bottom/back of the skeg or may not fully extend up to the lower gearcase. If you have questions, please call our office before installing the SkegPro

Note: If you have fitment questions, please call our office before installing the SkegPro

Step 2) Prep Your Skeg
Repair any damage to your skeg that will prevent the SkegPro from fitting correctly. Some lower units may have a reinforced wear tab at the bottom of the skeg. This wear tab should be filed flush with the skeg to provide a proper fit. If desired, you can also prime and paint the skeg before installing the SkegPro.

Step 3) Tap the SkegPro into Place
Using a mallet (leather, rubber, or wooden), place the SkegPro on the skeg and gently tap on it to get it started. Then drive it on with the mallet until fully seated into position.

Step 4) Install the Hardware
Using the pre-drilled mounting hole on the SkegPro as a pilot hole, drill into the skeg with the 3/16″ drill bit. Install the stainless steel screw and nylon locking nut.

Precautionary Statement: Megaware SkegPro is not designed to prevent damage in the event of a collision impact with stationary objects. The product is designed to prevent and reduce wear, and the amount of damage encountered while hitting minor floating objects or submerged stumps and rocks.